CAR OBD CODES
OBD/DTC Search, e.g.P0118
CAR OBD CODES P0118
P0118 OBD Code Definition:
P0118 Engine Coolant Temperature Sensor Circuit High
P0118 OBD Code Description:
OBD2 Code P0118 Definition:
The engine coolant temperature (ECT) sensor is a thermistor screwed into a coolant passage in the cylinder head. Sensor resistance is high when coolant temperature is low and resistance drops when coolant temperature increases. The powertrain control module (PCM) provides a 5 volt reference and a ground to the sensor. The PCM monitors voltage drop to determine coolant temperature. If the ECT reads less than freezing temp. when engine has been running for more than a few minutes, the PCM determines a circuit fault and sets this code. Or if the PCM determines the sensor resistance is out of specs, this code is set.
Symptoms
Possible sumptoms of P0118
Symptoms of a P0118 could include: Very poor fuel economy A no start condition Vehicle may start, but run very poorly, blowing black smoke, running very rough and misfiring Illumination of MIL
Possible Causes
Possible causes of P0118
A code P0118 may mean that one or more of the following has happened: A bad connection at the sensor An open in the ground circuit between the ECT sensor and the PCM A short in the voltage feed between the sensor and the PCM A bad PCM (less likely) A bad temperature sensor (shorted internally)
Possible Solutions
First, if you have access to a scan tool, check the reading of the coolant sensor. Does it read a logical number? If so, the problem is likely intermittent. Perform a “wiggle” test by wiggling the connector and harness to the sensor while watching the reading on the scan tool. Watch for any drop-outs. Drop-outs would indicate a bad connection. If the scan tool reads an illogical temperature, check the resistance of the temperature sensor. If it is out of specs, replace it. If it is in specifications, unplug the sensor and, using a fused jumper wire, jumper the two terminals of the connector together. The temperature reading should now be maxed out to above 250 degrees F. If not, there is likely a problem with the ground circuit or voltage supply. Check for 5 volts reference voltage at the connector. Also check for ground presence at the connector. If you do not have 5V ref. and/or ground continuity, check for these back at the PCM connector. If you have these at the PCM connector, then repair open or short between the PCM and the sensor. If you do not, remove the offending wire from the PCM and then check for proper voltage at the PCM pin. If it’s present now, repair short on the circuit. If it isn’t present after removing the wire and checking the pin, replace PCM NOTE: Usually, P0118 is indicative of a bad temperature sensor, but doesn’t rule out these other possibilities. If you’re unsure of how to diagnose a PCM, do not attempt. OBD-II Codes
P0115 P0116 P0117 P0118 P0119 P0125 P0128
Note: The information on the P0118 error code is purely informative, if you need more useful information, please consult your technician.
B11B4 B125A B2AE0 B1266 B1847 B002A B11BA B1812 B1093 B1C11 B2020 B2574 B11E8 B12DF B1B94 OBDII Chassis Codes
C0710 C1426 C1851 C1226 C109B C1021 C1456 C1268 C1402 C1778 C1472 C0003 C1A90 C0578 C2101 OBDII Network Codes
U2613 U0524 U0310 U2020 U0296 U0494 U200A U0164 U1201 U2355 U1950 U046A U1168 U0040 U0433 OBDII Powertrain Codes
P207D P1726 P22A9 P1257 P011D P2026 P0700 P014C P0276 P0680 P1184 P0712 P083A P0011 P1744