CAR OBD CODES
OBD/DTC Search, e.g.P0209
CAR OBD CODES P0209
P0209 OBD Code Definition:
P0209 Injector Circuit Malfunction Cylinder 9
P0209 OBD Code Description:
OBD2 Code P0209 Definition:
P0208 means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of P0209
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Possible Causes
Possible causes of P0209
The causes of a P0208 engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
Note: The information on the P0209 error code is purely informative, if you need more useful information, please consult your technician.
B0057 B1984 B2725 B1079 B1706 B2666 B1519 B1D03 B11AF B2543 B00C6 B129E B101F B266C B0515 OBDII Chassis Codes
C1281 C276B C2806 C1970 C1529 C1164 C195B C1A43 C0039 C111E C1799 C1880 C1319 C1774 C1945 OBDII Network Codes
U0523 U2100 U1176 U1212 U0207 U0326 U0484 U0111 U2517 U1230 U0425 U1126 U1234 U1736 U1054 OBDII Powertrain Codes
P0836 P0AA1 P0563 P1694 P0B00 P084E P0AE1 P045B P0522 P0ADD P0743 P1881 P0596 P0193 P1443