Home> OBDII Powertrain Codes>P1000 CAR OBD CODES

CAR OBD CODES

OBD/DTC Search, e.g.P1000

CAR OBD CODES P1000

P1000 OBD Code Definition:
P1000 OBD system readiness test not complete
P1000 OBD Code Description:

OBD Code P1000

OBD-II Monitor Testing Incomplete

OBD Code P1000

OBD system readiness test not complete

What’s mean?

OBD2 Code P1000 Definition:
The OBD monitors are performed during the OBD Drive Mode. The P1000 will be stored in continuous memory if any of the OBD monitors do not complete their full diagnostic check. Possible Causes

Possible causes of P1000
? Vehicle is new from the factory ? Battery or PCM had recently been disconnected ? An OBD monitor failure had occurred before completion of an OBD drive mode ? The PCM DTCs have recently been cleared with a M-MDS ? The PCM has been flashed and the vehicle has not yet completed an OBD drive mode. Possible Solutions

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE frame DATA HAS BEEN RECORDED ???Has the FREEZE frame DATA been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE frame DATA on the repair order, then go to the next step.
2	VERIFY REPAIR INFORMATION AVAILABILITY ???Verify related service repair information availability. ???Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	CHECK FOR ANY OTHER DTCS ???Where any other DTCs received with the P1000?	Yes	Go to the applicable DTC inspection.
3		No	Go to the next step.
4	REQUEST TO CLEAR DTC P1000 Note ???A complete OBD drive mode has not yet been performed to clear the DTC P1000 from the PCM. ???Has the customer requested the DTC P1000 be cleared?	Yes	Complete an OBD drive mode, then go to the next step.
4		No	Inform the customer that if the law in your area required additional driving in order to clear the DTC P1000 from the PCM memory, it must be complete before an inspection/maintenance test.
5	VERIFY THAT DTC P1000 TROUBLESHOOTING IS COMPLETED ???Make sure to reconnect all disconnected connectors. ???Clear the DTC from the PCM memory using the M-MDS. ???Start the engine and warm-up to normal operating temperature. ???Run the vehicle under the FREEZE frame DATA stored condition. ???Retrieve the DTC using the M-MDS. ???Is the PENDING CODE same DTC present?	Yes	Replace PCM, then go to the next step.
5		No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE ???Perform “After Repair Procedure”. ???Is there any DTC present?	Yes	Go to the applicable DTC inspection.
6		No	Troubleshooting completed.

Mercedes OBD Code P1000

Electronic Gear Selector Module: Defective N15/5

Note: The information on the P1000 error code is purely informative, if you need more useful information, please consult your technician.

Car brand: :

Ferrari, Maserati, BMW, Mobil, Alfa Romeo, Aston Martin, Audi, Bentley, Chevrolet, Citroen, Dodge, Fiat, Ford, Honda, Hyundai, Infiniti, Jaguar, Bugatti, Cadillac, Jeep, Lamborghini, Lancia, Land Rover, Lexus, Lincoln, Maybach, Mazda, Benz, Mitsubishi, Nissan, Opel, Pagani, Peugeot, Pontiac, Toyota, Volkswagen, Volvo, Porsche, Renault, Rolls - Royce, Saab, set, Skoda, Subaru, Suzuki, etc..